Laerdal.com  •  MySimCenter.com


Welcome to Simulation User Network Sign in | Join | Help

Search

You searched for the word(s):
Showing page 1 of 6 (58 total posts) < 1 second(s)
  • Re: simman & simpad linkbox

    Sorry, but&nbsp;SimPad do not support the Classic SimMan nor the Classic SimBaby that both use the 9-pin COM-port of product #380100. These two products are only supported&nbsp;by our&nbsp;PC Windows platform - LLEAP.
    Posted to General (Forum) by Dag Sanna on September 14, 2018
  • Re: Using Non-Laerdal Computers with LLEAP

    Hello Michael, Do you use multiple monitors on these computers? I.e. do you run both LLEAP (the instructor interface) and the learners Patient Monitor Application on the same computer but on different screens? The challenge with this is that the instructor and the learner must share the same mouse pointer. So if the learner touch the screen of ...
    Posted to General (Forum) by Dag Sanna on September 21, 2017
  • Re: Patient monitor freezes when first NIBP is activated

    Hello David, Could you please inform us what version of the simulator SW&nbsp;you are using. In the instructor application, navigate to the &lt;Help&gt; menu and then select &lt;About...&gt;. You should see the version number in that popup. This was a&nbsp;known issue in the old SimMan 3G software but should be fixed in the newer LLEAP SW. LLEAP ...
    Posted to SimMan 3G Technical (Forum) by Dag Sanna on April 13, 2016
  • 5 ways to read and/or write to/from a LLEAP simulator using the SDK

    This&nbsp;post describes 5 ways to communicate with a Laerdal Patient Simulator. The purpose is to help developers to decide the best method(s) for their needs. 1&nbsp;Remote Procedure Calls (RPC)The fundamentals behind all communication depends on the RPC available through LaerdalSimulatorAPI.dll. All the simulator functions can be accessed ...
    Posted to Simulator Tools & Software (Forum) by Dag Sanna on March 16, 2016
  • Example - how to support multiple versions of LLEAP from the same application

    We have suggested a solution that can be found attached. It contains an application that are able to load two version into the same process (but different appdomains). The demo shows how to do this and prints the following: &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Old SDK version = ...
    Posted to Simulator Tools & Software (Forum) by Dag Sanna on January 22, 2016
  • Exchange data between your SDK application and a simulation scenario made by SimDesigner

    Hello, Note that the SDK allows you to read and write from/to user defined variables and timers in a LLEAP scenario created with SimDesigner. This can be useful if you want to synchronize your application with a simulation session that runs in LLEAP. You can have the scenario write values to a variable in order to send a signal/information to ...
    Posted to Simulator Tools & Software (Forum) by Dag Sanna on November 24, 2015
  • Re: Laerdal Support for Windows 7 Enterprise

    Hello Sean, Enterprise and Ultimate are as you point out running identical binaries and are essentially identical out of the box. There is nothing in the old 3G legacy SW nor in LLEAP SW that prevents it from being used on Enterprise. However, Enterprise Windows computers are normally strictly controlled and restricted by policy rules enforced by ...
    Posted to General (Forum) by Dag Sanna on September 29, 2015
  • Re: Ventilation Data

    Hello, The value you are looking for is derived from the parameters mentioned further up in this thread. There is also a parameter named ''avgVentilationVolume'' that carry the derived value but it is not available&nbsp;from the SDK at the time. I'll write you mail where we can discuss this closer. Best regards
    Posted to Simulator Tools & Software (Forum) by Dag Sanna on September 14, 2015
  • Re: Can't connect to virtual manikin

    Hello, It's hard to say what goes wrong from your description. Do you attempt to connect to a physical manikin (simulator) or a virtual? Sound like a virtual server but I am not 100% sure. Check that the SDK and LLEAP is based on the same version.&nbsp;The current version&nbsp;for both is 5.3.0. Remember that if you use a physical manikin of the ...
    Posted to Simulator Tools & Software (Forum) by Dag Sanna on August 19, 2015
  • Re: Ventilation Data

    Hello Chris! I can see from your LinkedIn profile that you possesses DotNet programming skills. Then You probably will be able to use the LLEAP SDK to create an application that generates the logs you need. The SDK comes with several sample project that demonstrates most of what you need. In fact, it includes a project (described here ...
    Posted to Simulator Tools & Software (Forum) by Dag Sanna on May 5, 2015
1 2 3 4 5 Next > ... Last ยป